The **BE2** display on a Samsung washing machine points to **model/region dependent: jammed / continuously pressed button; mems / vibration sensor error**. Treat it as a diagnostic direction rather than a parts order: operating conditions, wiring, sensors, actuators, and control electronics can overlap. The exact stage when the code appears can be as important as the characters themselves. Note whether it happens at startup, during fill, heating, cooling, draining, spinning, drying, or after a power event. The display variants retained for this lookup are **BE2, bE2**. They are grouped under normalized key **BE2** so spacing, case, and separator differences do not create duplicate repair meanings.
Model compatibility: Samsung can reuse or reformat codes across series and model years, so BE2 may mean something different on another appliance or generation. Confirm this against your model’s documentation and record your full model number before acting.
Plain language
What this code means
The **BE2** display on a Samsung washing machine points to **model/region dependent: jammed / continuously pressed button; mems / vibration sensor error**. Treat it as a diagnostic direction rather than a parts order: operating conditions, wiring, sensors, actuators, and control electronics can overlap. The exact stage when the code appears can be as important as the characters themselves. Note whether it happens at startup, during fill, heating, cooling, draining, spinning, drying, or after a power event. The display variants retained for this lookup are **BE2, bE2**. They are grouped under normalized key **BE2** so spacing, case, and separator differences do not create duplicate repair meanings.
Signs
Symptoms you may notice
BE2 can be accompanied by this pattern: the control is not receiving an expected sensor signal or the signal is outside its accepted range.
The BE2 display becomes more meaningful if the appliance may stop a feature, limit operation, or repeat the code during the same stage.
The BE2 display becomes more meaningful if the affected function can behave intermittently if the signal or connection is unstable.
One clue that supports the BE2 diagnosis is that bE2 appears during the washer stage associated with jammed / continuously pressed button.
The BE2 display becomes more meaningful if the cycle can pause, stop, retry, drain, or refuse to advance until the condition is cleared.
Why it happens
Possible causes
see exact model manual — some models — Jammed / continuously pressed button
see exact model manual — some models — MEMS / vibration sensor error
Before you call
Safe checks you can make
These are simple, non-hazardous checks only. If anything is unclear, stop and contact a technician.
For BE2, start by doing this: photograph the code and note the exact operating stage when it appears.
The next non-invasive check is to check only user-accessible conditions that can physically affect the monitored function.
The next non-invasive check is to avoid replacing a sensor solely from the display; wiring, connectors, supply conditions, and the control can create the same result.
To rule out an accessible cause, record the code and the cycle stage where it appears.
The next non-invasive check is to check owner-accessible water supply, drain hose/filter, load balance, door, detergent, or power only when relevant.
As an external check for BE2, power-cycle once only where Samsung's guidance recommends it; if the same code reappears, move to model-specific diagnosis.
Important safety warning. Disconnect power and stop use for active leakage near electrical parts, smoke, burning smell, or repeated breaker trips. For BE2, stop troubleshooting immediately if the symptom crosses into a safety hazard rather than a normal diagnostic condition.
Get help
When to request repair service
If the code returns, model-specific sensor, harness, connector, and control-board testing is appropriate. If BE2 keeps returning, record the stage at which it reappears so the technician can test the model/region dependent: jammed / continuously pressed button; mems / vibration sensor error path instead of replacing parts by guesswork.
Book your repair
Seeing this code on your Samsung appliance?
Book a specialist visit for a clear estimate and approval before any repair.
Model/region dependent: Jammed / continuously pressed button; MEMS / vibration sensor error. Check the model-specific interpretation section below because Samsung publishes more than one verified meaning for this appliance+code key.
Resetting can clear a temporary state, not a persistent issue. If **BE2** comes back, preserve the code and move to the safe checks or model-specific service path.
Do not keep operating the appliance through a hazardous symptom just to see whether **BE2** clears. If there is heat, water, electrical, gas, or food-safety risk, stop and arrange diagnosis.
Not automatically. Samsung error codes are diagnostic indicators, not part numbers. Confirm the circuit around **BE2** before replacing anything.
Official Samsung support itself assigns different meanings to this code in different model/region contexts, so the exact model number matters. This page therefore keeps **Washer BE2** separate from same-looking codes used by other Samsung appliance families.
